{"product_id":"front-kdss-billet-link","title":"Dr KDSS Front KDSS Billet Fixed Link | 2010-2024 4Runner \u0026 GX460","description":"\u003cp\u003eA billet aluminum replacement for the OEM front passenger-side KDSS fixed link. It swaps the factory rubber bushing for a fully greaseable Delrin bushing system, so the front sway bar and suspension cycle freely instead of fighting built-up tension. Fits 2010+ 4Runner, GX460 and Prado 150 — KDSS-equipped vehicles only.\u003c\/p\u003e\u003ch3\u003eWhy It Exists\u003c\/h3\u003e\u003cp\u003eThe OEM front KDSS link uses a large rubber bushing torqued to 110 ft-lbs at ride height. Once torqued, that bushing is essentially locked in place — as the suspension cycles it resists rotation, tension builds in the link, and the suspension deflects instead of moving freely. Disconnect your sway bar and try rotating the OEM link by hand: it barely moves. This billet link removes that bind.\u003c\/p\u003e\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEliminates restriction from the OEM rubber bushing\u003c\/li\u003e\n\u003cli\u003eSmoother front suspension articulation and sway bar cycling under load\u003c\/li\u003e\n\u003cli\u003eReduces stored tension during suspension movement\u003c\/li\u003e\n\u003cli\u003eMaintains proper KDSS system function\u003c\/li\u003e\n\u003cli\u003eGreaseable, serviceable pivot point\u003c\/li\u003e\n\u003cli\u003eIntegrated pilot hole for optional safety wire\u003c\/li\u003e\n\u003cli\u003eDeveloped over 3+ years and 25,000+ hard miles — Baja race support, Baja tours, and SoCal high desert\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Specs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCNC-machined from thick 6061 billet aluminum, anodized\u003c\/li\u003e\n\u003cli\u003eFully greaseable Delrin bushing — controlled rotation without rubber bind\u003c\/li\u003e\n\u003cli\u003eWeight: 2.1 lbs\u003c\/li\u003e\n\u003cli\u003eDimensions: 8.5\" L × 4.5\" W × 1.25\" thick\u003c\/li\u003e\n\u003cli\u003eMarine grease or high-temperature performance grease recommended\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat's Included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e(1) Billet front KDSS fixed link\u003c\/li\u003e\n\u003cli\u003e(2) M12 × 1.25 × 50mm bolts\u003c\/li\u003e\n\u003cli\u003e(2) M12 × 1.25 Stover locking nuts\u003c\/li\u003e\n\u003cli\u003e(2) M12 washers (used only with older round-bushing setups)\u003c\/li\u003e\n\u003cli\u003eAll hardware clear zinc coated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eTorque Specs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTop main bolt (link to frame): 110 ft-lbs — Loctite or safety wire recommended\u003c\/li\u003e\n\u003cli\u003eVertical M12 sway bar bolts: 85 ft-lbs — no Loctite required (Stover nuts)\u003c\/li\u003e\n\u003cli\u003eMark bolts after torquing for visual inspection\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstall Notes\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eRemove the front skid plate for maximum clearance.\u003c\/li\u003e\n\u003cli\u003eSupport the sway bar with a hydraulic floor jack.\u003c\/li\u003e\n\u003cli\u003eRemove the two vertical sway bar bolts and the top frame bolt.\u003c\/li\u003e\n\u003cli\u003eLower the sway bar no more than 3\/8\" — the driver-side KDSS strut will begin to extend.\u003c\/li\u003e\n\u003cli\u003eRemove the OEM link.\u003c\/li\u003e\n\u003cli\u003ePre-grease the outside of the sleeve and the inside diameter of the Delrin bushing.\u003c\/li\u003e\n\u003cli\u003eInstall the billet link with the zerk fitting and pilot hole facing forward, and the sleeve bevel facing the inside of the frame.\u003c\/li\u003e\n\u003cli\u003eBefore final torque, inject grease until it exits the bushing. Minor bushing spread is normal and compresses at full torque.\u003c\/li\u003e\n\u003cli\u003eTorque all bolts to spec. Safety wire is recommended on the main bolt.\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eInstall Video\u003c\/h3\u003e\u003cp\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/qY9nExsAVE4\" title=\"Dr KDSS Front Billet Fixed Link Install\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/p\u003e","brand":"Dr KDSS","offers":[{"title":"Hardcoat Anodize(Gray Bronze Look)","offer_id":51364286824671,"sku":"DRK-FL-HC","price":200.0,"currency_code":"USD","in_stock":true},{"title":"Clear anodized","offer_id":51364286857439,"sku":"DRK-FL-CLR","price":200.0,"currency_code":"USD","in_stock":true},{"title":"Red","offer_id":51364286890207,"sku":"DRK-FL-RED","price":200.0,"currency_code":"USD","in_stock":true},{"title":"King gold","offer_id":51364286922975,"sku":"DRK-FL-GOLD","price":200.0,"currency_code":"USD","in_stock":true},{"title":"King blue","offer_id":51364286955743,"sku":"DRK-FL-BLUE","price":200.0,"currency_code":"USD","in_stock":true},{"title":"Black","offer_id":51364286988511,"sku":"frntlnkblk","price":200.0,"currency_code":"USD","in_stock":false},{"title":"Midnight Blue","offer_id":51364287021279,"sku":"frntlnkmdblue","price":200.0,"currency_code":"USD","in_stock":true},{"title":"Fox Orange","offer_id":51364287054047,"sku":"frntlnorng","price":200.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0812\/7289\/7759\/files\/Screenshot2026-02-19at9.40.09PM.png?v=1789045868","url":"https:\/\/yotamafia.com\/products\/front-kdss-billet-link","provider":"Yota Mafia","version":"1.0","type":"link"}